Every stage of its operation has been designed to make it reliable and discreet. When you turn your cooler on, the Brivis Contour begins its Pre-Wet cycle. Clean fresh water enters the cooler and begins soaking the cooling pads before the fan starts, ensuring that you will only be provided with cool fresh air. It is packed with features to give you comfort and flexibility.
The AquaSave cleans the water used in the cooling process avoiding any unnecessary wastage. The Brivis Contour also has one of the smallest water reservoirs on the market, holding up to a third the amount of water than other coolers, minimizing the amount of water discharged when the cooler is turned off.
The product information on this website comprising product brochures, warranty information, installation manuals, diagrams, specifications and representations relates to current products.
This information may be different for superseded products. For superseded products please contact Brivis to confirm product information. If ServoSeal not open Replace Networker and test again. Page 58 Cooler Operation cont. Fan Operation cont. Page Fan Operation Lower fan motor down and out of the mounting bracket.
Slide the winding coil out from the lamination plates. Replace upper pump housing assembly, if impellor damaged or jammed. Page Water Inlet Solenoid Operation cont. Water Inlet Solenoid Operation The Contour Cooler has a Volt water inlet solenoid on the under side of the base, at the high side of the roof.
The water inlet solenoid has a flexible hose attached with a filter inserted in the hose connections at each end. ServoSeal and Drain Valve Operation Contour and Profiler Coolers have a new and unique mechanism, to drain and empty the Cooler's tank and simultaneously close off the duct Contours only , at the end of use.
The ServoSeal is a set of adjustable louvers constructed in the Contour's base, which are driven closed and prevent heat loss from the building, when the unit is not in use.
Disconnect motor cam lever switch. Page 74 Check linkages are free moving and not jammed. Page 75 Replace N-E5 module and re test.
After the initial filling, at which point the water inlet solenoid turns OFF, the Cooler looses tank water volume due to evaporation, in the normal course of the unit's operation. Page 78 As the water level control probes will be constantly subjected to water and electrical power during normal operation, it is expected that a coating will eventuate, depending on the water quality.
Page 79 Error 50 is different and will cause a lockout, but provides the user the facility to reset the operation at the Networker. However, if the condition is still present after reset, the unit will lockout again. To rectify this condition, refer to Service Checks on page Page 81 Water inlet solenoid timed to fill for 70 seconds, then closes again.
Page 83 This condition will not harm the pump, but will result in poor and inadequate cooling performance. To rectify this condition, refer to Service Checks section. Page 84 This condition will not harm the pump, but will result in poor and inadequate cooling performance.
Page 85 Check the N-E5 8 Amp fuse is not open circuit. Page 86 Check for coating on the Water Sensor probes preventing circuit. Page 92 Cooler's maximum output midway between the minimum and maximum Output Selection figure , then the duct and outlet sizes should be increased to meet this level.
Page 93 Check the duct and fittings are insulated. Page Service Maintenance Service Maintenance Pre Season Maintenance The service to a Contour Cooler requires access to the home to check the performance of the unit through the duct system and the function of the wall control. Service work performed without access cannot be responsible for the system operation, only the Coolers function.
Page 97 Check the fan motor varies through the entire range. Check the minimum and maximum RPM setting are appropriate for the duct installation. Page 98 Check the Networker wall control is located in a suitable position for correct operation. Check the Coolers Pre Wet function is operating correctly. Check the unit operates in both Manual and Auto modes.
Page 99 Operate the pump for 5 minutes to rinse the pads and drain again. Refill the tank with clean water, operate the pump for 5 minutes to rinse the pads and drain again to complete. Page Service Maintenance Push the bushes out of the distribution tray.
Separate the roof outer and the inner distribution tray. Clean the components and reassemble. This manual is also suitable for: Advance Profiler. Print page 1 Print document pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR.
Don't have an account?
0コメント